LTC 9312/00
Instruction Manual
EN Indoor Dome
Housings
|
LTC 9312 Series | Instruction Manual | Unpacking
EN 3
1
UNPACKING
3
INSTALLATION
This mechanical equipment should be unpacked and
handled carefully.
1.
2.
3.
Remove the contents from the box.
Remove the ceiling tile in the desired location.
Check for the following items:
Qty.
Place the acrylic dome in the chosen location;
the dome will rest on the ceiling grid. (Be sure
the grid is adequately supported.)
Item
LTC 9312/00
Clear dome
Support channels
Black opaque liner
FM2 camera bracket assembly
Black dust cover
1
1
2
1
1
1
4.
5.
Using a utility knife or scissors, carefully cut a
hole in the black opaque liner, for the camera
to view through.
NOTE: Smaller cutouts allow more discreet
viewing.
If an item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems Inc. Sales Representative or Customer Service.
Place the black opaque liner into the acrylic
dome and rotate it to the desired viewing
position.
The shipping carton is the safest container in which the
unit may be transported. Save it for possible future use.
6.
7.
Align the long slots of two FM2 camera
bracket arms.
Using a carriage bolt, 5/16in. washer, 1/4in.
washer, lockwasher, and hex nut, attach the
bracket arms together loosely. See FIGURE 1.
2
SERVICE
If the unit ever needs repair service, the customer
should contact the nearest Bosch Security Systems, Inc.
Service Center for return authorization and shipping
instructions.
8.
Slide the smaller channel through the slot on
the larger support channel. See FIGURE 2.
Use the 1/4 x 20 bolt supplied to connect the
FM2 to the support channels (via the center
hole in the two channels). BE CAREFUL
WHEN HANDLING THE SUPPORT
CHANNELS; EDGES MAY BE SHARP.
Service Centers
USA
Phone:
fax:
800-366-2283 or 717-735-6638
800-366-1329 or 717-735-6639
9.
Securing tabs are provided to hold the bracket
between the liner. Bend the corresponding tab
with a screwdriver.
CCTV Spare Parts
Phone:
fax:
800-894-5215 or 408-956-3853 or 3854
408-957-3198
e-mail:
Canada
Phone:
10. Connect the camera to the FM2 bracket, and
place the assembly in the dome so the edges
of the bracket rest on the flange of the dome.
514-738-2434
Europe, Middle East & Asia Pacific Region
Phone: 32-1-440-0711
For additional information, see
11. Tighten all connections and complete wiring
the camera.
12. A tex-wipe is provided to clean the dome.
13. Place the black dust cover over the top of the
dome, so the dust cover is sitting on the
supporting channels.
USE ONLY WITH A CLASS 2 POWER
SUPPLY.
For added flexibility, the camera can be mounted on
either the short or the long side of the bracket arm.
Bosch Security Systems | 28 July 2004
|
LTC 9312 Series | Instruction Manual | Parts List
EN 4
PARTS LIST
FIGURE 2
FIGURE 1
Part No.
Qty. Description
1
2
3
4
5
6
7
8
9
90-BTCA01
30-VL696
92-WSSL01
91-NTHH02
30-VL732
92-WSFL05
92-WSFL01
90-BTHH11
2
1
2
2
1
1
1
2
1/4-20 x 3/4in. Zinc Carriage
4 in 1 Camera Bracket
1/4 Split Lockwasher 18-8 SS
1/4-20 Hex Nut 18-8 SS
0-1 Multiple Camera Bracket
5/16 Flat Washer SS
1/4 SAE Flat Washer 18-8 SS
1/4-20 x 1/2 Hex Head Zinc
-009 O-ring
96-RSORNG 1
FIGURE 3
Bosch Security Systems, Inc.
850 Greenfield Road
Bosch Security Systems B.V.
P.O. Box 80002
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Lancaster, PA 17601 USA
Tel: 800-326-3270
Fax: 1-717-735-6560
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 80000
Singapore 577180
Republic of Singapore
Tel: 65 (6) 319 3486
© 2004 Bosch Security Systems GmbH
3935 890 15212 04-31 | Updated July 28, 2004 | Data subject to change without notice.
|